Differences

This shows you the differences between two versions of the page.

--- usage:using_stock:train_hud [2020-12-23 15:03]
ywang
+++ usage:using_stock:train_hud [2022-06-29 13:30]
56independent [Passenger] Add note for LuaATC
@@ Line 1: / Line 1: @@
 ====== Train HUD ======
+Passengers and drivers of trains get more information about the train they are in with a HUD.
-===== Driver =====
+===== Graphical driver HUD =====
-For the driver, the current train HUD looks similar to the following:
+The graphical driver HUD was introduced in version 2.2.0 and updated in 2.2.1.
+{{:usage:ywang_trainhud_design_1.png?direct&400|}}
+The HUD shows:
+  * The speed in m/s indicated by the two-digit 7-segment display.
+  * The corresponding speed shown as a white bar.
+  * The physical speed limit (i.e. the speed limit of the wagons themselves), if lower than 20m/s.
+  * The driving direction of the train as a lever
+  * The throttle and brake controls of the train shown as a combined lever
+  * "ATC" when ATC is active
+  * "LZB" when LZB is active
+  * "Shunt" when shunt mode is active
+  * The signal aspect of the next signal shown by two rectangles and a number:
+    * If the upcoming signal allows proceeding without any speed limit, the indicator is shown in green.
+    * If the upcoming signal has a speed limit that is higher than 0m/s, the indicator is shown in orange, and the speed limit is shown as a red triangle pointing downward at the speed bar.
+    * If the upcoming signal does not allow proceeding, the indicator is shown in red.
+  * The status of the doors.
+  * The speed current speed limit of the train (if present) shown as a red vertical bar
+  * The ATC target speed (if present) shown as a cyan triangle pointing up
+===== Passenger =====
+Passengers only see the text shown inside the train, as configured on the onboard computer or LuaATC.
+===== Text-based driver HUD =====
+A text-based HUD was used before version 2.2.0. It looks similar to the following:
 <code>
  [F] {B - >o< +} >|< >|<
@@ Line 29: / Line 56: @@
       * The ATC command and delay (if any) is shown after the ATC target speed
     * When LZB is active (e.g. when the train is approaching the end of the track) **and** the train is manually controlled, ''-!- Safety override -!-'' is shown.
-===== Passenger =====
-Passengers only see the text shown inside the train.
-===== (Proposed) New Driver HUD =====
-The following driver HUD is designed and available in the ''trainhud'' branch in the source code.
-{{:usage:ywang_trainhud_design_1.png?nolink&400|}}
-The HUD shows:
-  * The speed in m/s indicated by the two-digit 7-segment display.
-  * The driving direction of the train ("Forward" or "Reverse")
-  * The lever of the train:
-    * "EMG" for emergency brake
-    * "B" for normal brake
-    * "R" for roll
-    * "N" when the speed of the train is constant
-    * "P" for acceleration (**p**ower)
-  * "ATC" when ATC is active
-  * "LZB" when LZB is active
-  * "Shunt" when shunt mode is active
-  * The signal aspect of the next signal:
-    * A red square when the next signal is red or when the train approaches the end of the track
-    * An orange square when the next signal has speed restriction higher than 0m/s
-    * A green square when the next signal allows proceeding without speed restriction
-  * "Left Door" or "Right Door" when the door on the left or right side of the driving direction is open
-  * The speed of the train shown as a white bar
-  * The speed current speed limit of the train (if present) shown as a red vertical bar
-  * The speed restriction of the next signal (if present and greater than 0m/s) shown as a red triangle pointing down
-  * The ATC target speed (if present) shown as a cyan triangle pointing up

Advanced Trains

User Tools

Site Tools

Differences

Page Tools